Saturday, April 24, 2010

Fabricating the Exhaust Shields






The exhaust shields for my Tiger were the first installed, and field-fabricated by repair crews. That being said, they were thin, and certainly designed for utility instead of cosmetic value. Keep in mind, they probably didn't have an elaborate bending brake, and cut the shapes with a torch. As you fabricate yours, keep this in mind. On the 1/35th scale parts I have seen that are of this type of shield, they have a very delicate louver cut and bended, which I doubt the field crews would have done.


What you need are a sharp pair of scissors, knife with sharp #11 blades, needle files, and one thing that really helped me was a pair of drafting dividers. I used the dividers to scale out the size this shield should be, and transfer the dimensions to a pattern. Being the nice guy that I am, my sketch of the part is above the text.


I used 0.010" brass sheet for the part. Follow the sketch, and with scissors, cut the overall size. Then, cut the side slots where the shield fits over the 3-bolt exhaust cover on each side. Round the corners where I have indicated using a needle file. To cut the vent slots, I marked the location on the sheet with a pencil, and then used a diamond cut-off wheel in my Dremel at a slow speed. Brace the part, and also your hand that is holding the Dremel. Take your time, and it should be straight. Cutting the slots will leave some burrs around the hole; you can clean these with a sharp #11 blade. Use a flat needle file to smooth out everything. Lastly, align the fold line on something that has a nice, straight edge, and slowly bend. The bend should be slightly less than 90-degrees. The shield is wider where it mounts to the rear hull.



To mount this on the Tiger, I glue a very narrow strip of 0.010" plastic, about 1/8" wide x 1/2" long, going up vertically from the middle of the 3-bolt exhaust mount on each side. This is a little bit of my imaginative engineering. Namely; the real field crews had to have something other than the hull-rear to weld this sheet shield to. Hey-it looks right to me. Then, using superglue, glue the shield in place. You may need to trim slightly to get a good fit-then try it again. Also, since these shields were sheet metal, they were beaten up easily. Now is a good time to take a plier and bend them a little, if so desired. Hint: If you have a slight fit problem, this can help/cover it up. If you do it right, it should look correct; like the photo at the top of the post.

To finish up in the rear, I reinstalled the jack, after cleaning it up. The crank for the starter (C32) is pretty weak, and was broken, so it was replaced with brass rod that was bent to shape. I removed the mounts for the crank from the plastic piece, and drilled these out with a pin vise to accept the new brass crank. I also saved the square socket from the end of the plastic crank and attached it to the brass replacement. Watch out for the starter plate (D2). On later Tigers, Tamiya has this correct in a straight up-and-down mount. But on the very early Tigers, this was a diagonal mount, so I reinstalled the starter plate diagonally. With this, I was done on the rear.





Saturday, April 17, 2010

Exhaust, Part 2




So I finally received the plastic bits (rod, tube, angle, etc.) that I needed. If you check the Plastruct website, individual pieces can be ordered, but be careful. The minimum order is $25, so it takes A LOT, unless you have another project looming that you need material for.

I removed the installed mufflers, (Parts D1 and D15). This was a headache. Tube glue and huge locating holes. I filled and sanded the holes in the rear hull, and then repaired where needed on part D15. To correct the muffler, I removed part D17, the raised deflector, as it wasn't on this version. After I cut the legs for this, I simply cleaned the recess in the top of the muffler, and filled it using rod, cut into a disc, about 1.5 mm thick. I wanted this to be flat across the top of the muffler. Then, I took a thin slice of 0.16" rod, and glued it in the center of the muffler-this will be the exhaust flapper. The flapper looks a little concave in the drawings that I have, so I took 320-grit, and rounded it a little on the edges.

For the flapper hinge, I took a very sharp #11 blade, and cut a notch in the flapper that I had just made, starting at the center of the flapper, and going to the edge. The hinge should be in the middle of the exhaust rear, and I am just trying to simulate a hinge. A small section of plastic rod cut to length, serves as the pin.

There are five bolts that need represented, and in the real Tiger, these were a recessed screw. Yeah; I'm not doing that. Instead, I am going with a raised bolt-head, which will give about the same visual effect. To do this, I cut 5 pieces of very small rod, about 1" long. Here's a tip: Make sure that the ends of your cut are dead flat and square, using a very sharp blade. This will make the next step easier.

To get the bolt pattern, I dabbed a little liquid glue on one end of the 1" piece of rod, and using tweezers, attached it to the area of the muffler between the outer diameter and the flapper. I glued the first piece directly opposite the hinge pin, and then one on each side of the hinge pin. The last two pieces were affixed in-between these. Once the glue is dry-and I mean really dry-I used a very sharp side-cutter, and cut these off to where they are just barely above the surface of the top of the exhaust.

One thing that I need to point out, too. My exhausts are knowingly too tall, but it was done for the ease of construction. Here's why. The rod inserted in the existing exhaust made my life easier, but in reality, the outer walls of the exhaust should have been trimmed down 1.5 mm to where the molded top was. My method, like I said, made my life easier, but if you do the math, if this were a real Tiger, my correction would be 4" taller than it should. I'm not about to fuss over that, though.

So now that the mufflers are reinstalled, it is time to make those louvered exhaust shields. Time to find an empty aluminum can....

Saturday, March 27, 2010

Correcting the Exhaust (and Waiting on Parts)

Looking at Steps 12 and 13 of the Instructions.

The dual exhausts on the kit, parts D1, D15, are accurate for the early Tiger. However, Part D17 is an elevated outlet cover on four short legs above the exhaust outlet. My references say this wasn't installed until sometime in early-mid 1943, which is a little late for the Tunisian Tiger. So I will delete that. One thing that is missing from the exhaust is a hinged flapper cover for each exhaust, that by this time was standard on the Tiger. The flappers will be scratchbuilt using some Plastruct rod, cut to size. Here is where I am waiting on parts.

The rear exhaust was also equipped with sheet metal shields. The original shields were field-installed by maintenance crews in Tunisia, and you can see these both as fully-rounded, or squared corner. My photos say either is correct, and should also have three louvers spaced in the top half of each side of this shield. Since it will be easier to form these using the squared-corner design, I will go with that one. I will fabricate these out of thin aluminum, which means another trip to the hobby store for supplies. That being said, the Tamiya-supplied shields (Part D12) are perfect and nicely done for any version other than the very early Tiger 1.

Here's a tip, too. While I am back here doing some work, there are some very large mounting holes in the rear hull that I will fill and sand, too.

Another thought, while waiting for parts, is that of the engine grills and tool clamps, which are still somewhere in process from Roll Models. In other words, until this stuff shows up, work on the lower hull is coming to a screeching halt. More to follow.....

Sunday, March 14, 2010

Attaching The Top Deck to The Lower Hull




Sure, this sounds easy. But like Billy Mays always said, “Wait…there’s more!”

First off, The Top Deck (from Step 15 of the Instructions) will be warped. All of mine are to some extent, and this one is no different. You will need to get some heavy rubber bands, and in my case, some small Irwin Quick-Grip clamps, ready. Make sure that the pin marks on the edges of the Top Deck, especially at each rear side, are sanded smooth.

Also, the Front Glacis, Part B3, has two significant pin marks at the top-rear, that should be filled and sanded before you mount the Top Deck. Once these are addressed, run a bead of plastic cement around the full area of the Lower Hull sides where the Top Deck will meet, and inside the front and rear channel for the Top Deck. Insert the Top Deck into the channel in the Front Glacis (B3), then pull it down into the rear channel, and start matching up along the sides. Clamp and band to keep the seam as even as possible. On mine, rubber bands worked well, and they were used around the hull in both side-to-side and end-to-end fashion. At the areas where the warpage was worse, I had to apply slight pressure with a clamp at the right front corner, and the left side just ahead of the engine deck. Once the glue dries, inspect your seam line, fill as needed, and sand smooth.

With all of the sanding done so far, weld seams will need to be re-done. After the glue is dry and the clamps come off.

There are a few things to note, too. The driver's periscope, was ignored from Step 10, since it cannot be seen from the outside. The MG 34 in the Front Glacis (F2) was removed from the ball mount (B1-B3), and the ball mount was left in place. Since this is an exterior-only build, we can mount the machine gun barrel only, after painting, from the outside. Also, at a later time, we will address the two periscopes missing from the hatches. These can also be done from the outside, since Tamiya designed no periscopes coming through the hull, anyway.

Sunday, March 7, 2010

The Front Mudguards



The front mudguards are a decent representation of the real ones, but they need improved. In real life, these were hinged on the outer 1/3, and Tamiya has this hinge molded, but it isn't great, and there is no latching mechanism like in real life. There is a very slight panel line where the two parts meet, but this should be a true cut on the ends where the hinge does not cover it. All of this could be improved, by filing off the hinge, cutting the mudguards where they should, then scratch building hinges, latches, etc. But, these mudguards weren't used until early 1943, and my Tunisian Tiger predates that, which used a different style mudguard. For the earliest Tigers, you will see an unhinged mudguard, that is angled about 10-degrees further than the angle on the front glacis, and then at the mid-point, it has a bend that sends the outer half about another 10-degrees down. These mudguards were also covered in tread plate.

It was time to get the Dremel, and with my cut-off disc, removed the existing mudguards. While there, and you will see this in the photo, it was time to smooth the cut using a file and sandpaper (320), and filling the gap that was hidden under the mudguard.

The replacement will be fabricated using sheet stock, cut to size, and with the correct angle in the middle. Then, I will cover that with scale deck plate, which is available in that scale for car models. Again, check out the local hobby shop or Roll Models. Since I don't have any deck plate, finishing the mudguards will wait.

On Accuracy and Weathering. My Opinion

A few short words on detail, accuracy, and scale effect. First, and this is my opinion, unless you are really into it, or putting your kit into a show or contest, I think that a lot of detailing is over-done. If you look at some of the kits in the previously-mentioned Guide to The Tiger Tank, these guys painfully reproduce every last nut, bolt, and fastener. Good for them, but I'm not into it. My take: remember scale-effect. In 1/25 scale, for instance, and using the normal viewing distance of an arms-length, the real life equivalent would be if you were standing 75 feet away from the real tank. I wouldn't see a wing nut on a tool fastener, and with my eyes, I might have a hard time even counting the road wheels. My feeling is that if the kit part has a close representation, then I am fine with that. That is not to say that I will overlook accuracy, though. I will try to make it as historically accurate as I can. (My next post will expose some of that, and the end-result)

Another example: On page 111 of The Guide to Tiger Tank, it has a picture of the front headlight and the etched mounting bracket they used. Apparently, the real-life bracket that they used for the example was an intricate, angle-iron based support, with miter cuts, mounting bolts, etc. It is crazy-detailed, and in scale (1/35) size, I cannot imagine what that would be like. Since I am building a Tunisian Tiger, and the headlights required the mount on the front plate, I need to use something like that. But then, since this was a field modification in real life, I just cannot imagine these field crews doing anything other than the most basic construction, which to me, would be correct, too. So on mine, it will be a representation of a simple pair of plates welded to the hull that hold the headlight up. Easier for me, and almost impossible to refute.

And weathering? Some, to me, is just completely overdone. Yes, I know that they get dirty, dusty, and muddy in real life. But unless I am putting it in a diorama, all of the caked-on mud looks silly. Plus, again in my opinion, why do you want to do all of the crazy paint detail, dry-brushing, etc., just to obscure it under mud? Again, it is about preference, but I like light weathering.

One more point is painting the thing. Take the Tunisian Tiger, for instance. These were originally in German Grey, then painted green. In the field. Which means, these crews did it using what they had. Behind the road wheels, under the fenders, hull bottom, etc., shouldn't be green, except for where over spray would hit. That is how I want to represent mine. Think Earl Scheib. And I don't get these extensive fade effects, either. Sure, it wasn't the best quality paint that was used in real life. But I see heavy sun fading being represented, with the "pre-shading, post-shading, spraying almost white in panel centers, blah-blah-blah", and I shake my head. Again, to me it is overdone, and I make a slightly lighter top than bottom, but the real ones just didn't survive that long-especially the early ones-to get that faded. Some of them are faded more than that old '34 Ford that was parked in the meadow at my Grandpa's that was still there in the mid-80's.

Time to redirect, and get back to the build.

A Few Words About References


If you model the Tiger Tank, there are more references than you ever need. These are available via the internet, books, magazine articles, etc. Of course, you already know this. The best of these, in my opinion, is "The Modeler's Guide to The Tiger Tank", written by Patrick Stansell with Bruce Culver. It was released a few years ago, and I am not even sure where I found it, but it is incredible. Not only does it feature numerous builds (and these guys are museum-quality builders), but you will find kit resource lists, identification drawings from the real tanks, and even a disposition list of actual tank chassis numbers. Unbelievable. Here is a great link to a review of the book, via the Edmonton IPMS:

http://www.ipmsedmonton.com/April%202004web.pdf